Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Ultramid® A3Z HP - PA66-I - BASF

Material Data Center offers the following functions for Ultramid® A3Z HP:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Ultramid A datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
機械的特性 - 熱的特性 - その他の特性. - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
商品の説明文
Impact-modified and stabilized injection moulding grade for components and housing with good low temperature impact resistance.
機械的特性乾燥/調湿単位テスト基準
ISO データ
引張弾性率 1900 / 1060 MPa ISO 527
降伏応力 50 / - MPa ISO 527
降伏ひずみ 5 / - % ISO 527
破壊呼びひずみ 45 / - % ISO 527
シャルピー衝撃強さ, +23°C N / N kJ/m² ISO 179/1eU
シャルピー衝撃強さ, -30°C N / N kJ/m² ISO 179/1eU
ノッチ付きシャルピー衝撃強さ, +23°C 90 / 113 kJ/m² ISO 179/1eA
ノッチ付きシャルピー衝撃強さ, -30°C 28 / 19 kJ/m² ISO 179/1eA
熱的特性乾燥/調湿単位テスト基準
ISO データ
溶融温度, 10°C/min 262 / * °C ISO 11357-1/-3
荷重たわみ温度, 1.80 MPa 64 / * °C ISO 75-1/-2
荷重たわみ温度, 0.45 MPa 170 / * °C ISO 75-1/-2
その他の特性.乾燥/調湿単位テスト基準
密度 1070 / - kg/m³ ISO 1183
Processing Recommendation Injection Molding値単位テスト基準
Pre-drying - Temperature ≤80 °C -
Pre-drying - Time 2 - 4 h -
Processing humidity ≤0.2 % -
樹脂温度 280 - 304 °C -
金型温度 60 - 100 °C -
特殊な特性
成形加工法.
射出成形.
特殊な特性.
高耐衝撃及び耐衝撃改良.
領域別の利用可能性
北アメリカ.
その他の情報
村遜速揃
Max. Water content: 0.20%
Product is supplied in sealed containers and
drying prior to molding is not required. If drying
becomes necessary, a dehumidifying or desiccant dryer
operating at 80 degC (176 degF) is recommended. Drying time is
dependent on moisture level, but 2-4 hours is generally
sufficient.
Further information concerning safe handling procedures
can be obtained from the Material Safety Data Sheet.
Alternatively, please contact your BASF representative.
PROCESSING
Melt Temperature 280-304 degC (536-580 degF)
Mold Temperature 60-100 degC (140-212 degF)
Injection and Packing Pressure 35-125 bar (500-1500 psi)
Back Pressure 0-0.35 MPa (0-50 psi)
Screw Speed 40-80 rpm
Screw Compression Ratio 3:1 to 4:1

This product can be processed over a wide range of mold
temperatures; however, for applications where aesthetics are
critical, a mold surface temperature of 60-100 degC (140-212 degF)
is recommended.

Injection pressure controls the filling of the part and should
be applied for 90% of ram travel. Packing pressure affects
the final part and can be used effectively in controlling
sink marks and shrinkage. It should be applied and maintained
until the gate area is completely frozen off.
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.